You are viewing: "Nozzles"


Blast Machine Accessories > Nozzles
  

Boron Carbide Lined Metal Jacketed BSD Series

A blast nozzle accelerates the air and abrasive as the mixture exits the end of the hose. The taper and length of the nozzle's inlet and outlet determine the pattern and velocity of the abrasive exiting the nozzle. The composition of the liner material determines its resistance to wear.

Requirements for Operation
Nozzles are sized by the diameter of their orifices in 1/16-inch increments. A No. 2 nozzle has a 2/16-inch (1/8-inch) orifice, a No. 3 nozzle has a 3/16-inch orifice, etc. The size of the nozzle orifice determines abrasive and air consumption. Air consumption is measured in cubic feet per minute (cfm) at a given pressure.

When choosing a nozzle, consider the amount of available air in cfm, the capacity of the blast machine and the inside diameter of the piping, and the blast and air hoses. For optimal performance, these elements must be compatibly sized.

If too large a nozzle is used, low blast pressure and rapid wear on the blast hose will occur. If too small a nozzle is used, smooth media flow will be difficult to achieve.

Description of Operation
The operator inserts the nozzle washer into a contractor-thread nozzle holder and screws in the nozzle, turning it by hand, until it seats firmly against the washer.

With all related equipment correctly assembled and tested, the operator points the nozzle at the surface to be cleaned and presses the remote control handle to begin blasting. The operator holds the nozzle 18 to 36 inches from the surface and moves it smoothly at a rate that produces the desired cleanliness. Each pass should overlap slightly.

The operator must replace the nozzle once the orifice wears 1/16-inch beyond its original size.

Advantages

  • Boron Carbide liner material is the most abrasive-resistant, durable, and economical liner material.
  • Long-venturi nozzles allow high production blasting at a distance of 18 to 24 inches for hard-to-clean surfaces, and 30 to 36 inches for loose paint and soft surfaces.
  • Expected life with expendable abrasives is approximately 1000 hours.
  • 1-inch entry provides smooth transition and maximum productivity with 1-inch ID blast hose.

Replacement Parts
NW-4 nozzle washers
(10)..............................00869


Nozzle Stock Number, Dimensions and Weights

 
Model No.
Stock No.
Orfice ID
Length
Net Wt.
Pkg'd Wt.
Fine 1-1/4" Thread BSD-4 1419 1/4" 5-7/16" 1 lb 1.5 lb
BSD-5 1420 5/16" 5-7/8" 1 lb 1.5 lb
BSD-6 1421 3/8" 6-13/16" 1.2 lb 1.5 lb
BSD-7 1422 7/16" 8-1/8" 1.3 lb 1.5 lb
BSD-8 1423 1/2" 9" 1.5 lb 2 lb


Available Literature:
21978 - Metal-Jacketed, Silicon Carbide-Lined
21979 - Urethane-Jacketed, Silicon Carbide-Lined
21986 - Metal-Jacketed, Tungsten Carbide-Lined
23414 - Rubber-Jacketed, Tungsten Carbide-Lined
24184 - Metal-Jacketed, Boron Carbide-Lined
24185 - Metal-Jacketed, Tungsten Carbide-Lined CT Series


Blast Machine Accessories > Nozzles
  

Clemlite® Lined Metal Jacketed Long Venturi

A blast nozzle accelerates the air and abrasive as the mixture exits the end of the hose. The taper and length of the nozzle's inlet and outlet determine the pattern and velocity of the abrasive exiting the nozzle. The composition of the liner material determines its resistance to wear.

Long Venturi: SFD, SMD, SSD, SXD

Requirements for Operation
Nozzles are sized by the diameter of their orifices in 1/16-inch increments. A No. 2 nozzle has a 2/16-inch (1/8-inch) orifice, a No. 3 nozzle has a 3/16-inch orifice, etc. The size of the nozzle orifice determines abrasive and air consumption. Air consumption is measured in cubic feet per minute (cfm) at a given pressure.

When choosing a nozzle, consider the amount of available air in cfm, the capacity of the blast machine and the inside diameter of the piping, and the blast and air hoses. For optimal performance, these elements must be compatibly sized.

If too large a nozzle is used, low blast pressure and rapid wear on the blast hose will occur. If too small a nozzle is used, smooth media flow will be difficult to achieve.

Description of Operation
The operator inserts the nozzle washer into a contractor-thread nozzle holder and screws in the nozzle, turning it by hand, until it seats firmly against the washer.

With all related equipment correctly assembled and tested, the operator points the nozzle at the surface to be cleaned and presses the remote control handle to begin blasting. The operator holds the nozzle 18 to 36 inches from the surface and moves it smoothly at a rate that produces the desired cleanliness. Each pass should overlap slightly.

The operator must replace the nozzle once the orifice wears 1/16-inch beyond its original size.

Advantages

  • Expected life with expendable abrasives is up to 500 hours
  • Durable metal jacket
  • Non-binding contractor threads
  • 42% lighter than tungsten carbide

Replacement Parts
For flanged nozzle use coupling lock-springs
(25)..............................21585


Nozzle Stock Number, Dimensions and Weights

 
Model No.
Stock No.
Orfice ID
Length
Net Wt.
Pkg'd Wt.
Flanged SFD-6 01623 3/8" 6-7/8" 1.1 lb 1.5 lb
SFD-7 01624 7/16" 8-1/16" 1.2 lb 2 lb
SFD-8 01625 1/2" 9-1/4" 1.3 lb 2 lb
Contractor Thread SMD-3 04520 3/16" 4-5/16" .70 lb 1 lb
SMD-4 04521 1/4" 5-7/16" .80 lb 1 lb
SMD-5 04522 5/16" 5-7/8" .80 lb 1 lb
SMD-6 04523 3/8" 6-3/4" .90 lb 1 lb
SMD-7 04524 7/16" 8" 1 lb 1 lb
SMD-8 04525 1/2" 9" 1 lb 1 lb
Fine 1-1/4" Thread SSD-3 01617 3/16" 4-5/16" .60 lb 1 lb
SSD-4 01618 1/4" 5-7/16" .60 lb 1 lb
SSD-5 01619 5/16" 5-13/16" .70 lb 1 lb
SSD-6 01620 3/8" 6-13/16" .80 lb 1 lb
SSD-7 01621 7/16" 7-15/16" 1.1 lb 1.5 lb
SSD-8 01622 1/2" 9" 1.3 lb 1.5 lb
Contractor Thread SXD-6 04592 3/8" 6-13/16" 1 lb 1.5 lb
SXD-7 04593 7/16" 8-1/16" 1.2 lb 1.5 lb
SXD-8 04594 1/2" 9-3/16" 1.3 lb 1.5 lb


Available Literature:
21978 - Metal-Jacketed, Silicon Carbide-Lined
21979 - Urethane-Jacketed, Silicon Carbide-Lined
21986 - Metal-Jacketed, Tungsten Carbide-Lined
23414 - Rubber-Jacketed, Tungsten Carbide-Lined
24184 - Metal-Jacketed, Boron Carbide-Lined
24185 - Metal-Jacketed, Tungsten Carbide-Lined CT Series


Blast Machine Accessories > Nozzles
  

Clemlite® Lined Rubber Jacketed Long Venturi

Long Venturi: SAS, SMS, SXS

A blast nozzle accelerates the air and abrasive as the mixture exits the end of the hose. The taper and length of the nozzle's inlet and outlet determine the pattern and velocity of the abrasive exiting the nozzle. The composition of the liner material determines its resistance to wear.

Requirements for Operation
Nozzles are sized by the diameter of their orifices in 1/16-inch increments. A No. 2 nozzle has a 2/16-inch (1/8-inch) orifice, a No. 3 nozzle has a 3/16-inch orifice, etc. The size of the nozzle orifice determines abrasive and air consumption. Air consumption is measured in cubic feet per minute (cfm) at a given pressure.

When choosing a nozzle, consider the amount of available air in cfm, the capacity of the blast machine and the inside diameter of the piping, and the blast and air hoses. For optimal performance, these elements must be compatibly sized.

If too large a nozzle is used, low blast pressure and rapid wear on the blast hose will occur. If too small a nozzle is used, smooth media flow will be difficult to achieve.

Description of Operation
The operator inserts the nozzle washer into a contractor-thread nozzle holder and screws in the nozzle, turning it by hand, until it seats firmly against the washer.

With all related equipment correctly assembled and tested, the operator points the nozzle at the surface to be cleaned and presses the remote control handle to begin blasting. The operator holds the nozzle 18 to 36 inches from the surface and moves it smoothly at a rate that produces the desired cleanliness. Each pass should overlap slightly.

The operator must replace the nozzle once the orifice wears 1/16-inch beyond its original size.

Advantages

  • Expected life with expendable abrasives is up to 500 hours
  • Durable rubber jacket
  • 1-inch entry provides smooth transition and maximum productivity with 1-inch ID blast hose
  • 1-1/4-inch entry ensures maximum productivity with 1-1/4-inch ID blast hose

Nozzle Stock Number, Dimensions and Weights

 
Model No.
Stock No.
Orfice ID
Length
Net Wt.
Pkg'd Wt.
Fine 1-1/4" Thread SAS-4 28079 1/4" 5-3/4" .95 lb 1 lb
SAS-5 28080 5/16" 6-1/8" 1.0 lb 1 lb
SAS-6 28081 3/8" 7-1/8" 1.15 lb 1.2 lb
SAS-7 28082 7/16" 8-1/26" 1.30 lb 1.5 lb
SAS-8 28083 1/2" 9-1/2" 1.45 lb 1.5 lb
Contractor Thread SMS-4 100864 1/4" 5-3/4" .70 lb 1 lb
SMS-5 100865 5/16" 6-1/8" .75 lb 1 lb
Contractor Thread SXS-6 100866 3/8" 7-1/8" .9 lb 1 lb
SXS-7 100867 7/16" 8-1/2" 1.10 lb 1.5 lb
SXS-8 100868 1/2" 9-1/2" 1.20 lb 1.5 lb


Available Videos:

Clemlite® Rubber-Jacketed, Silicon Carbide-Lined


Available Literature:

28505 - Clemlite® Rubber-Jacketed, Silicon Carbide-Lined
Clemlite® Rubber-Jacketed Cross Reference Guide
21978 - Metal-Jacketed, Silicon Carbide-Lined
21986 - Metal-Jacketed, Tungsten Carbide-Lined
23414 - Rubber-Jacketed, Tungsten Carbide-Lined
24184 - Metal-Jacketed, Boron Carbide-Lined
24185 - Metal-Jacketed, Tungsten Carbide-Lined CT Series


Blast Machine Accessories > Nozzles
  

Tungsten Carbide Lined Angle CAM Series
A CAM angle nozzle is designed to blast blind surfaces such as mold cavities or behind beams. Tungsten Carbide lined, the nozzles are available in one or three outlets. 

Description of Operation
The operator inserts the included nozzle washer into a nozzle holder and screws in the nozzle, turning it by hand, until it seats firmly against the washer.

With all related equipment correctly assembled and tested, the operator points the angle nozzle at the surface to be cleaned and presses the remote control handle to begin blasting. The operator holds the nozzle 18 to 36 inches from the surface and moves it smoothly at a rate that produces the desired cleanliness. Each pass should overlap slightly.

The operator must replace the nozzle once the orifice wears 1/16-inch beyond its original size.

Advantages

  • Tungsten Carbide is the most rugged and durable liner materal and provides the best value.
  • Has a 45 degree outlet angle and is available in one or three outlets.
  • 1-inch entry provides smooth transition

Replacement Parts
NW-3 Nozzle Washers
(Pkg of 10)..............................21583


Nozzle Stock Number, Dimensions and Weights

 
Model No.
Stock No.
Orfice ID
Length
Orifices
Pkg'd Wt.
1-1/4" Thread CAM 4 x 1
01442 1/4" 3" 1 1.5 lb
CAM 4 x 3 01444 1/4" 3" 3 1.5 lb
CAM 5 x 1 01445 5/16" 3-1/8" 1 1.5 lb
CAM 5 x 3 01447 5/16" 3-1/8" 3 1.5 lb
CAM 6 x 1 01448 3/8" 2-3/4" 1 1.5 lb
CAM 6 x 3 01450 3/8" 2-3/4" 3 1.5 lb


Available Literature:
21978 - Metal-Jacketed, Silicon Carbide-Lined
21979 - Urethane-Jacketed, Silicon Carbide-Lined
21986 - Metal-Jacketed, Tungsten Carbide-Lined
23414 - Rubber-Jacketed, Tungsten Carbide-Lined
24184 - Metal-Jacketed, Boron Carbide-Lined
24185 - Metal-Jacketed, Tungsten Carbide-Lined CT Series


Blast Machine Accessories > Nozzles
  

Tungsten Carbide Lined Metal Jacketed Long & Short Venturi

Short Venturi: CJD
Long Venturi: CSD, TXD, SDX, CXD

A blast nozzle accelerates the air and abrasive as the mixture exits the end of the hose. The taper and length of the nozzle's inlet and outlet determine the pattern and velocity of the abrasive exiting the nozzle. The composition of the liner material determines its resistance to wear.

Requirements for Operation
Nozzles are sized by the diameter of their orifices in 1/16-inch increments. A No. 2 nozzle has a 2/16-inch (1/8-inch) orifice, a No. 3 nozzle has a 3/16-inch orifice, etc. The size of the nozzle orifice determines abrasive and air consumption. Air consumption is measured in cubic feet per minute (cfm) at a given pressure.

When choosing a nozzle, consider the amount of available air in cfm, the capacity of the blast machine and the inside diameter of the piping, and the blast and air hoses. For optimal performance, these elements must be compatibly sized.

If too large a nozzle is used, low blast pressure and rapid wear on the blast hose will occur. If too small a nozzle is used, smooth media flow will be difficult to achieve.

Description of Operation
The operator inserts the nozzle washer into a contractor-thread nozzle holder and screws in the nozzle, turning it by hand, until it seats firmly against the washer.

With all related equipment correctly assembled and tested, the operator points the nozzle at the surface to be cleaned and presses the remote control handle to begin blasting. The operator holds the nozzle 18 to 36 inches from the surface and moves it smoothly at a rate that produces the desired cleanliness. Each pass should overlap slightly.

The operator must replace the nozzle once the orifice wears 1/16-inch beyond its original size.

Advantages

  • Rugged and durable aluminum jacket.
  • Tungsten carbide is the most rugged and durable liner material and provides the best value.
  • Expected wear-life when blasting with expendable abrasives is approximately 300 hours.
  • TXD nozzles with large contractor threads eliminate galling or binding of the threads in the holder
  • CXD nozzles provide smooth transition from 1-1/4-inch blast hose to the 1-1/4-inch entry for users who prefer 1-1/4-inch fine thread nozzles.

Replacement Parts
For flanged nozzle use coupling lock-springs
(25)..............................21585 


Nozzle Stock Number, Dimensions and Weights

 
Model No.
Stock No.
Orfice ID
Length
Net Wt.
Pkg'd Wt.
Fine 1-1/4" Thread CJD-3 1378 3/16” 3-1/8" .70 lb 1 lb
CJD-4 1379 1/4" 3-1/8" .70 lb 1 lb
CJD-5 1380 5/16" 3-1/8" .70 lb 1 lb
CJD-6 1381 3/8" 3-1/8" .80 lb 1 lb
CJD-7 1382 7/16" 3-1/8" .80 lb 1 lb
CJD-8 1383 1/2" 3-1/8" .90 lb 1 lb
Fine 1-1/4" Thread CSD-3 1384 3/16" 4-1/4" 1.1 lb 1.5 lb
CSD-4 1385 1/4" 5-3/8" 1.3 lb 1.5 lb
CSD-5 1386 5/16" 5-3/4" 1.3 lb 1.5 lb
CSD-6 1387 3/8" 6-3/4" 1.6 lb 2 lb
CSD-7 1388 7/16" 8" 2 lb 2 lb
CSD-8 1389 1/2" 9" 2.4 lb 2.5 lb
Fine 1-1/4" Thread CXD-6 23460 3/8” 6-3/4” 1.6 lb 2 lb
CXD-7 23461 7/16” 8” 2 lb 2 lb
CXD-8 23462 1/2” 9” 2.5 lb 2.5 lb
Contractor Thread TXD-6 99147 3/8" 6-3/4" 1.9 lb 2 lb
TXD-7 99148 7/16" 8" 2 lb 2.5 lb
TXD-8 99149 1/2" 9-9/16" 2 lb 2.5 lb
Flanged SDX-6 1394 3/8" 6-3/4" 2.2 lb 3 lb
SDX-7 1395 7/16" 8-3/4" 2.2 lb 3 lb
SDX-8 1396 1/2" 9-3/16" 2.4 lb 3 lb
SDX-10 1397 5/8" 9-3/16" 2.8 lb 3.5 lb
SDX-12 1398 3/4" 9" 2.9 lb 3.5 lb


Available Literature:
21978 - Metal-Jacketed, Silicon Carbide-Lined
21979 - Urethane-Jacketed, Silicon Carbide-Lined
21986 - Metal-Jacketed, Tungsten Carbide-Lined
23414 - Rubber-Jacketed, Tungsten Carbide-Lined
24184 - Metal-Jacketed, Boron Carbide-Lined
24185 - Metal-Jacketed, Tungsten Carbide-Lined CT Series


Blast Machine Accessories > Nozzles
  

Tungsten Carbide Lined Metal Jacketed Short Straight Barrel CT Series

A blast nozzle accelerates the air and abrasive as the mixture exits the end of the hose. The taper and length of the nozzle's inlet and outlet determine the pattern and velocity of the abrasive exiting the nozzle. The composition of the liner material determines its resistance to wear.

Short Straight Barrel CT Series

Requirements for Operation
Nozzles are sized by the diameter of their orifices in 1/16-inch increments. A No. 2 nozzle has a 2/16-inch (1/8-inch) orifice, a No. 3 nozzle has a 3/16-inch orifice, etc. The size of the nozzle orifice determines abrasive and air consumption. Air consumption is measured in cubic feet per minute (cfm) at a given pressure.

When choosing a nozzle, consider the amount of available air in cfm, the capacity of the blast machine and the inside diameter of the piping, and the blast and air hoses. For optimal performance, these elements must be compatibly sized.

If too large a nozzle is used, low blast pressure and rapid wear on the blast hose will occur. If too small a nozzle is used, smooth media flow will be difficult to achieve.

Description of Operation
The operator inserts the nozzle washer into a contractor-thread nozzle holder and screws in the nozzle, turning it by hand, until it seats firmly against the washer.

With all related equipment correctly assembled and tested, the operator points the nozzle at the surface to be cleaned and presses the remote control handle to begin blasting. The operator holds the nozzle 18 to 36 inches from the surface and moves it smoothly at a rate that produces the desired cleanliness. Each pass should overlap slightly.

The operator must replace the nozzle once the orifice wears 1/16-inch beyond its original size.

Advantages

  • Tungsten Carbide liner material is the most rugged and durable. It is also the best value in a liner material.
  • Short nozzles (CTs) are designed for blasting 3 to 6 inches away from the surface.
  • Expected life with expendable abrasives is approximately 300 hours.
  • 1/2-inch entry provides smooth transition and maximum

Replacement Parts
NW-1 Nozzle Washers
(Pkg of 10)..............................21580


Nozzle Stock Number, Dimensions and Weights

 
Model No.
Stock No.
Orfice ID
Length
Net Wt.
Pkg'd Wt.
3/4" Thread CT-2 1351 1/8" 1-3/4" .30 lb .5 lb
CT-3 1352 3/16" 1-3/4" .30 lb .5 lb
CT-4 1353 1/4" 1-3/4" .30 lb .5 lb
CT-5 1354 5/16" 1-3/4" .30 lb .5 lb
CT-6 1355 3/8" 1-3/4" .20 lb .5 lb
CT-8 1356 1/2" 1-3/4" .20 lb .5 lb


Available Literature:
21978 - Metal-Jacketed, Silicon Carbide-Lined
21979 - Urethane-Jacketed, Silicon Carbide-Lined
21986 - Metal-Jacketed, Tungsten Carbide-Lined
23414 - Rubber-Jacketed, Tungsten Carbide-Lined
24184 - Metal-Jacketed, Boron Carbide-Lined
24185 - Metal-Jacketed, Tungsten Carbide-Lined CT Series


Blast Machine Accessories > Nozzles
  

Tungsten Carbide Lined Rubber Jacketed Long & Short Venturi

Short Venturi: TJP, TYP
Long Venturi: TSP, TMP, TXP

A blast nozzle accelerates the air and abrasive as the mixture exits the end of the hose. The taper and length of the nozzle's inlet and outlet determine the pattern and velocity of the abrasive exiting the nozzle. The composition of the liner material determines its resistance to wear.

Requirements for Operation
Nozzles are sized by the diameter of their orifices in 1/16-inch increments. A No. 2 nozzle has a 2/16-inch (1/8-inch) orifice, a No. 3 nozzle has a 3/16-inch orifice, etc. The size of the nozzle orifice determines abrasive and air consumption. Air consumption is measured in cubic feet per minute (cfm) at a given pressure.

When choosing a nozzle, consider the amount of available air in cfm, the capacity of the blast machine and the inside diameter of the piping, and the blast and air hoses. For optimal performance, these elements must be compatibly sized.

If too large a nozzle is used, low blast pressure and rapid wear on the blast hose will occur. If too small a nozzle is used, smooth media flow will be difficult to achieve.

Description of Operation
The operator inserts the nozzle washer into a contractor-thread nozzle holder and screws in the nozzle, turning it by hand, until it seats firmly against the washer.

With all related equipment correctly assembled and tested, the operator points the nozzle at the surface to be cleaned and presses the remote control handle to begin blasting. The operator holds the nozzle 18 to 36 inches from the surface and moves it smoothly at a rate that produces the desired cleanliness. Each pass should overlap slightly.

The operator must replace the nozzle once the orifice wears 1/16-inch beyond its original size.

Advantages

  • Short-venturi nozzles (TJP, TYP) designed for blasting 12 to 18 inches away from the surface.
  • Long-venturi nozzles (TSP, TMP, TXP) allow high production blasting at a distance of 18 to 24 inches for hardto- clean surfaces, and 30 to 36 inches for loose paint and soft surfaces
  • Expected life with expendable abrasives is approximately 300 hours
  • Durable natural rubber jacket
  • 1-inch entry provides smooth transition and maximum productivity with 1-inch ID blast hose
  • 1-1/4-inch entry ensures maximum productivity with 1-1/4-inch ID blast hose

Nozzle Stock Number, Dimensions and Weights

 
Model No.
Stock No.
Orfice ID
Length
Net Wt.
Pkg'd Wt.
Fine 1-1/4" Thread TJP-3 23507 3/16" 3-3/4" .60 lb 1 lb
TJP-4 23508 1/4" 3-3/4" .60 lb 1 lb
TJP-5 23509 5/16" 3-3/4" .70 lb 1 lb
TJP-6 23510 3/8" 3-3/4" .70 lb 1 lb
TJP-7 23511 7/16" 3-11/16" .80 lb 1 lb
TJP-8 23512 1/2" 3-11/16" .80 lb 1 lb
Contractor Thread TYP-3 23501 3/16" 3-3/4" .70 lb 1 lb
TYP-4 23502 1/4" 3-3/4" .70 lb 1 lb
TYP-5 23503 5/16" 3-3/4" .70 lb 1 lb
TYP-6 23504 3/8" 3-3/4" .80 lb 1 lb
TYP-7 23505 7/16" 3-3/4" .80 lb 1 lb
TYP-8 23506 1/2" 3-3/4" .80 lb 1 lb
Fine 1-1/4" Thread TSP-3 23513 3/16" 4-3/4" 1 lb 1.5 lb
TSP-4 23514 1/4" 5-3/4" 1.2 lb 1.5 lb
TSP-5 23515 5/16" 6-1/4" 1.2 lb 1.5 lb
TSP-6 23516 3/8" 7-3/4" 1.6 lb 2.0 lb
TSP-7 23517 7/16" 8-1/2" 2.0 lb 2.0 lb
TSP-8 23518 1/2" 9-5/8" 2.5 lb 2.5 lb
Contractor Thread TMP-3 23519 3/16" 4-3/4" 1 lb 1.5 lb
TMP-4 23520 1/4" 6" 1.2 lb 1.5 lb
TMP-5 23521 5/16" 6-1/4" 1.3 lb 1.5 lb
TMP-6 23522 3/8" 7-1/4" 1.7 lb 2.0 lb
TMP-7 23523 7/16" 8-1/2" 2.0 lb 2.5 lb
TMP-8 23524 1/2" 9-3/4" 2.5 lb 2.5 lb
Contractor Thread TXP-6 23525 3/8" 7-3/8" 1.8 lb 2.0 lb
TXP-7 23526 7/16" 8-1/2" 2.4 lb 2.5 lb
TXP-8 23527 1/2" 9-3/4" 2.3 lb 2.5 lb


Available Literature:
21978 - Metal-Jacketed, Silicon Carbide-Lined
21979 - Urethane-Jacketed, Silicon Carbide-Lined
21986 - Metal-Jacketed, Tungsten Carbide-Lined
23414 - Rubber-Jacketed, Tungsten Carbide-Lined
24184 - Metal-Jacketed, Boron Carbide-Lined
24185 - Metal-Jacketed, Tungsten Carbide-Lined CT Series



 Showing results 1 to 7 of 7


| Home | ©2017 Clemco Industries Corp.